Living Clean Journey Continues Pdf Here

Comments from our Members

1. This article is a work in progress and will continue to receive ongoing updates and improvements. It’s essentially a collection of notes being assembled. I hope it’s useful to those interested in getting the most out of pfSense.

   pfSense has been pure joy learning and configuring for the for past 2 months. It’s protecting all my Linux stuff, and FreeBSD is a close neighbor to Linux.

   I plan on comparing OPNsense next. Stay tuned!

   ---

   Update: June 13th 2025

   Diagnostics > Packet Capture

   I kept running into a problem where the NordVPN app on my phone refused to connect whenever I was on VLAN 1, the main Wi-Fi SSID/network. Auto-connect spun forever, and a manual tap on Connect did the same.

   Rather than guess which rule was guilty or missing, I turned to Diagnostics > Packet Capture in pfSense.

   1 — Set up a focused capture

   

   pfSense_Diagnostics_Packet-Capture1400×1226 141 KB

   Set the following:

   • Interface: VLAN 1’s parent (ix1.1 in my case)
   • Host IP: 192.168.1.105 (my iPhone’s IP address)
   • Click Start and immediately attempted to connect to NordVPN on my phone.

   2 — Stop after 5-10 seconds
   That short window is enough to grab the initial handshake. Hit Stop and view or download the capture.

   3 — Spot the blocked flow
   Opening the file in Wireshark or in this case just scrolling through the plain-text dump showed repeats like:

   192.168.1.105 → xx.xx.xx.xx  UDP 51820
   192.168.1.105 → xxx.xxx.xxx.xxx UDP 51820
   

   UDP 51820 is NordLynx/WireGuard’s default port. Every packet was leaving, none were returning. A clear sign the firewall was dropping them.

   4 — Create an allow rule
   On VLAN 1 I added one outbound pass rule:

   

   Action:  Pass
   Protocol:  UDP
   Source:   VLAN1
   Destination port:  51820
   

   The moment the rule went live, NordVPN connected instantly.

   Packet Capture is often treated as a heavy-weight troubleshooting tool, but it’s perfect for quick wins like this: isolate one device, capture a short burst, and let the traffic itself tell you which port or host is being blocked.

   Update: June 15th 2025

   Keeping Suricata lean on a lightly-used secondary WAN

   When you bind Suricata to a WAN that only has one or two forwarded ports, loading the full rule corpus is overkill. All unsolicited traffic is already dropped by pfSense’s default WAN policy (and pfBlockerNG also does a sweep at the IP layer), so Suricata’s job is simply to watch the flows you intentionally allow.

   That means you enable only the categories that can realistically match those ports, and nothing else.

   Here’s what that looks like on my backup interface (WAN2):
   

   

   pfsense_suricata_minimal_WAN2_rules2561×3035 511 KB

   The ticked boxes in the screenshot boil down to two small groups:

   • Core decoder / app-layer helpers – app-layer-events, decoder-events, http-events, http2-events, and stream-events. These Suricata needs to parse HTTP/S traffic cleanly.
   • Targeted ET-Open intel –
     emerging-botcc.portgrouped, emerging-botcc, emerging-current_events,
     emerging-exploit, emerging-exploit_kit, emerging-info, emerging-ja3,
     emerging-malware, emerging-misc, emerging-threatview_CS_c2,
     emerging-web_server, and emerging-web_specific_apps.

   Everything else—mail, VoIP, SCADA, games, shell-code heuristics, and the heavier protocol families, stays unchecked.

   The result is a ruleset that compiles in seconds, uses a fraction of the RAM, and only fires when something interesting reaches the ports I’ve purposefully exposed (but restricted by alias list of IPs).

   That’s this keeps the fail-over WAN monitoring useful without drowning in alerts or wasting CPU by overlapping with pfSense default blocks.

   Update: June 18th 2025

   I added a new pfSense package called Status Traffic Totals:
   

   

   pfSense_Status_Traffic_Totals1400×1259 93.3 KB

   Update: October 7th 2025

   Upgraded to pfSense 2.8.1:
   

   

   image667×909 68.9 KB

2. Fantastic article @hydn !

   Over the years, the RFC 1918 (private addressing) egress configuration had me confused. I think part of the problem is that my ISP likes to send me a modem one year and a combo modem/router the next year…making this setting interesting.

   I see that Netgate has finally published a good explanation and guidance for RFC 1918 egress filtering:

3. I did not notice that addition, thanks for sharing!